Hills Fabrication & Welding
Hills Fabrication & Welding is a mobile and workshop based fabrication and welding business servicing
đź“ŤWe are now located at Unit 21/244 Beringarra ave Malaga! Directly behind the old premises.
We also have a new email, for all enquires please contact [email protected]
A pair of track guides pre-fabricated and installed on site for the Red Hill waste management facility!
Low profile skids completed last year ✔️
Sure has been awhile, HF&W has been all go for the past few months so things have been a little quite on here.
Starting things back up with a wall we installed for the Eastern Metropolitan Council at the Red Hill waste management facility.
This includes a large gate for forklift access with a quick and easy coded locking door!
Hills Fabrication crane hire coming early 2024.
Just enough time to give it a birthday and paint.
Crane safe registered - 900kg at 16.5m reach.
Quick wear plate change out and dent removal out of the base for the first bucketđź’Ą
Also a more recent urgent repair on a loader bucket where the sides down low had worn through, quick plate up to get them out of troubleđź’Ą
Keeping downtime to a minimum is our aim.
Plastic filtration hood completed and installed with adjustable suction dampeners and adjustable sitting height.
No drawings, just told to make it work 🔥
Tipper floor reline and new two way tailgate hinge done for Red Hill waste management.
This was capping over the existing floor as requested - full wire wheel and rust convert of the old floor followed by galv painting the undersides of the new sheets to prevent rusting underneath.
Unimog has been working just about 7 days a week since the start of the year from when it got put to work.
Few small issues ironed out but safe to say the old rig is going great!
Stage 1 of the hopper turn shaft completed some time ago now with installation just about finished up on site đź‘Ś happy days!
Patio truss kit done to drawings some time ago for a great local builder, headed off to powder coat.
Recent modifications and repairs to this drop deck.
Sheeted off the front, added heavy duty mesh down the centre, boxed off the front with tray sides and pull out/swing away rear gate for a place to store attachments and smaller parts.
As we pulled up the old wooden boards unfortunately above the skid plate wet dirt/sand had accumulated and severely rusted the PFC supports and skid plate/king pin welds. Removing all the old parts gave the chance to completely remove all the rust and heavily treat the chassis. New 12mm skid, king pin and fresh PFC supports has it ready to be put back to work!
Weld in sea container lock boxes - $110+gst each supplied or $275+gst installed within 15km radius from either Malaga or mount Helena, further locations happily arranged and discounts with installed price apply for multiple lock boxes.
Installed 3 last week for the Red Hill tip after they where having issues with break ins.
Aluminium drop in handrail completed some time ago for Mentis Australia!
Hills Fabrication has been flat out the past few months so as you can expect the socials have been a little quite.
Will be getting through all my office work today to everyone i haven’t got back to yet, apologies for the delays!
-Fresh cutting edge in ✔️
-Trim down rake bucket to allow it to fit into GP bucket for easier transport/manoeuvring ✔️
Fresh headboard for this tray recently completed, also made up some fresh hinges and re-installed the side gates.
This tray came in severely rusted after being modified and used as a chipper body and the client was needing it changed back to factory.
Off for a thorough sand blast and paint, happy days!
A bolt together pergola frame finished in satin black powder coat recently completed.
Hills Fabrication has teamed up along side Cygnus high risk solutions to offer a hassle free solution to small/medium size structural steel supply and installation with tight access not being an issue!
Hills Fabrication not only has the ability to manufacture structural steel out of our workshop in Malaga but is also equipped with one of the most capable mobile welding units in WA to ensure your structural steel project is completed start to finish.
Cygnus high risk solutions is the perfect compliment with there compact but very capable spider crane for all of our site installations.
We are two departments working together to offer a one stop shop for your next structural steel supply + installation.
contact:
[email protected]
An older style rock pick bucket partial rebuild - new floor skin, rust repairs where necessary, new strapping and its good to go!
⚡️BENDING + HOLE PUNCHING ⚡️
Hills Fabrication can now offer bending and hole punching - from sheet metal to 10mm mild steel plate, custom brackets and much more.
Get in touch with a description and quantity for a free quote.
-0409156108
[email protected]
A day out on site in Woottating modifying this hopper. The client needed the opening to be on the opposite side to where it was so a new opening was plasma cut out, the panel that had been cut out was then welded into the original opening to stop any spillage.
Lastly the original exit was cut out and enlarged to stop any clogging.
No job to big or to small for the unimog!
Some much needed maintenance carried out on this tipper trailer.
Cut outs and patches done in the required areas of the floor and damaged cross members replaced, tidied up the rear upright to stop the rust and welded up some cracks on the tower and headboard.
Ready to be put back to work.
A completed job that was finished up some time ago now. Truck came in with a pretty mangled and bent head board - new skin on the headboard + some straightening and it was good to go.
Customer also requested a slight extension of the rear to give a bit more wriggle room between the ramps and his machinery, this also helped with stiffening up the rear.
Haven’t been as active on here as I would’ve liked to have been but we are finally through the busiest month to date.
I apologise to everyone who has tried to get in contact with me or receive a quote. Very long hours in the workshop left very minimal time to do any office work.
I’ll be in contact with everyone ASAP and get back into quoting.
Thanks everyone!
Hills Fabrication finally back in action!
After much more time off then first anticipated the unimog is finally ready for service.
The bigger setup deserved a larger diesel welder so we are now running a vantage 575 to ensure no job is too big!
I apologise to everyone I haven’t got in contact with, it’s been a crazy few weeks getting this ready and I will be getting back to everyone asap!
I hope everyone has a great new year.
As another year comes to an end I’d like to thank everyone for your continued support! Wether it be as simple as engaging with my posts or letting me take care of your projects nothing goes unnoticed and I am very grateful to all of you for making this possible.
2023 will soon look a little different as I begin to setup the new HF&W mobile welding truck and of course it’s a unimog!
With its larger carrying capacity, bigger tray and off-road capability soon no job will be off the chart.
for now I will be off until the 9th of January but in this time I will be completing quotes and catching up in the office, which I apologise for my lack of lately!
I hope everyone has a great and safe new year.
Hot dipped galvanised handrail completed some time ago now.
Had the great opportunity to take care of the steel work for this horse stable RM Smith and Sons are currently building.
Awesome project to be involved in and a great team to work a long side.
Thanks Randall!
A modular bolt together shade house frame completed!
Fabricated in the workshop, delivered and installed on siteâś…
A concrete in 3x bin enclosure for the chidlow volunteer bush fire brigade recently completed âś…
Click here to claim your Sponsored Listing.
Videos (show all)
Category
Contact the business
Website
Address
Perth, WA
6090
12 May Hollman Drive, Bassendean
Perth, 6054
ALLOY. The authentic metal mosaic tile. Sleek, solid, unique and designed to last a lifetime.
37 Roscoe Street , Henderson
Perth, 6166
We are an independent supplier of wear solutions to a number of industries, including mining, minera
Unit 3/41 Pavers Circle
Perth, 6090
Quality Australian Made Products @ gecko fab we believe in attention to detail. Always looking for ways to improve and help our customers get the best products - made locally. L...
108 Radium Street Welshpool
Perth, 6106
Operating from purpose-built premises in Welshpool, Simcraft employs highly-qualified tradesmen and
72 Erceg Road, Yangebup
Perth, 6164
Acute Fabrication is located in Perth, Australia supplying a wide range of fabrication welding, main
Perth
Creating custom light metal fab work for your home, anything from unique plant stands to decorative outdoor/indoor features!
Perth, 6210
handcrafted weapons taking your ideas and putting the laughing coffin spin on it.
Perth, 6090
Western Metalworx provide custom metal fabrication services to the Mining, Industrial and Commercial