Bay Area Pump And Well Service LLC

Is hydrofracturing a 100% guarantee for making a well better? There is no guarantee, but with hydro-fracturing, there is a 98% chance that it will work perfectly and more clean water will pool into the well.

You may have only heard of geothermal wells recently, but using geothermal energy isn't a new idea. One of the first ways humans harnessed geothermal power was hot springs.

Watering the garden on a water meter can become very expensive, especially during the summer. If you are in a dry climate, you will benefit from drilling a well on your land. This will provide you with ample amounts of irrigation water even in the dry months.

Did you know that one of the most common causes of water well contamination is the failure to seal the space between the well casing and the hole in the ground properly? Some materials that can seal this space are cement grout, concrete, or bentonite.

It's a good idea to do some preliminary research before drilling for water. Location is certainly important, as is the presence of potential well water contaminants like: a leaking septic system, landfill pollution and pesticide runoff from big agribusiness.

Before drilling a water well, contact the county health department to find out what permits are required and what regulations must be followed. There may be setback requirements for potential sources of contamination such as septic systems, livestock, landfills, or agricultural runoff.

If your well is not producing an adequate amount of water to meet your demands, there are some solutions. Hydro-fracturing is a beneficial process that can increase your well's yield by accessing water from nearby sources.

Rusty wells are usually caused by iron or manganese in the groundwater. Water that is off-smelling is usually caused by sulfur, which is also known to corrode plumbing.

Looking to add value to your property? While it might not be the first thing on your list, a well can make a big difference. Many people prefer the taste of well water and will pay more for a house that has a private well attached to it.

Until recent centuries, all wells were hand-dug, which means that people used shovels to dig below the water table. In some developing countries, these wells remain an important source of potable water.

Deeply drilled wells offer greater protection from bacterial contamination. Why? As groundwater travels through multiple layers of soil, sand, rock and clay, larger numbers of bacteria die off or are filtered from the water.

The filtration system used in well water is much more environmentally friendly than that of large water plants in urban areas, since water wells decrease chemical and industrial pollution during the filtration process.

How do I know if the fractures created by hydrofracturing are clean? Since the process uses such high pressure, the water and pressure will clean out any and all newly created fractures made during the process.

In rotary drilling, a drill bit (made of tough metals such as tungsten) is attached to a drill pipe and rotated to break through layers of rock.

Can you guess the percent of U.S. households that rely on well water for their everyday needs? If you guessed 15 percent or so, you're right. Although wells can be located in urban areas, a majority are found in rural locations.

The earliest wells date back to the Neolithic era. The oldest well found so far was in a submerged village off the coast of Israel, and dates back to around 8000 B.C.E.

In 1900-1901, the first mud-circulated drilling operation was conducted at Big Hill in Beaumont, TX. Drilling through softer, younger formations, Capt. Anthony Lucas and his crew bored a well 1,100 feet deep, which gushed oil 200 feet into the air.

Geothermal wells use geothermal energy, such as hot springs, to heat and cool homes. Heat is either released into the home or pulled out of it.

Drilled wells are those water wells that are constructed by a combination of jetting and driving. Farms commonly use this type of well and the well is generally 4 to 8 inches in diameter. These wells if properly constructed have a low risk of contamination.

Did you know well drilling is the fastest way to reach hidden groundwater sources? Of course, well drilling should only take place after you have had your ground source tested for safety and the regulations in your area (regarding private well ownership) confirmed beforehand.

After you have your water well drilled and installed, it is a good idea to pick up an emergency generator to have on hand in the event of a power outage so the water pump will keep working.

Water wells and water basins have existed for thousands of years. In fact, history tells us the ancient Phoenicians and Abyssinians (among others) had their own wells. Indeed, water wells were dug by hand until the early 19th century.

Did you know that in low yielding wells, it’s sometimes possible to increase yield by using what’s called a hydrofrac technique? Here, selected parts of the drilled hole are subjected to great pressure using special tools in the hope that existing fractures will be enlarged and allow the well to connect to additional water bearing fissures.

Did you know that the first mechanically drilled water well was created by using a hollow sycamore tree with a four-foot diameter? The tree was sawed off and placed in mire to obtain salt water below.

When water is filtered at a treatment plant, it has to go through a complicated filtering process that uses a lot of energy and chemicals. Well water, on the other hand, is filtered through layers of stone and sand to remove contaminants naturally.

Depending on the formation at the bottom of a well, a screening device, filter pack, slotted casing, or open bore hole will be left to allow water to flow into the well.

When your well is complete, you will be provided a well construction record. Keep the record, and pass it on to any future owners of your home.