Konrad's Garage

AE86 X S13 tension rod conversion for my boy

made a sick shifter/hydro panel for while I mounted his rear mount radiator and reinforced his latch system. Pretty sweet car! Excited to put some more work in it in the future!

Fixed up this leaky aluminium throttle body in which someone at some point decided to try to fill the holes with steel filler. Wild. Should be good to go now!

Corvette adventures with this weekend.
We got this wonderful fitted in C5 Vette. Love the cage kits stuff!

Always love seeing this 1JZ SC here. Intercooler fell off so we made some new tabs to keep it sturdy and raised up.

Miata Roll Bar all done!
1.5” .120 wall DOM
Built to clear all convertible mechanisms and provide safety in the event of a roll over. Thank you to for supplying some rods for harness loops and for bringing me extra tubing as well as letting me break in his sick Baileigh notcher.

FREE SHIPPING on all Pedal Commander units on the website! Contact us directly with questions or if you need help finding one for your vehicle!

Crashed BMW had a questionable repair in the past. and I chopped the old frame rails, welded on new ones sourced by customer, cut the factory tubs out and tubed them for full functionality with the SLR angle kit. Straightened out the intercooler mounting as well and it’s almost ready to go with the turbo S52 it’s getting. Can’t wait to see it ripping again.

Fully sealed S13 Hatch firewall for safety and cabin smoke purposes utilizing bulk head connectors for a completely sealed unit.

Repaired and Flocked dash for the 1J car. It was a disaster to begin with but it came out very nice!

and I finalized this Z cage by adding some intrusion bars this weekend.

and I knocked out this roll cage this weekend. It came out great after a few adjustments!

2 more lines and fluids left. It’s almost ready for start up.

Did some maintenance on this gorgeous 60s Chevy yesterday.

Drift cars are hoopties. Staying busy getting this thing ready to be tuned. Waiting for new wastegate and then it’s go time! Getting close! After it’s drivable, I’ll be addressing the rear fab work as I want to change a couple things.

Came in with a no start issue, ended up with wiring gremlins sorted and a complete clutch overhaul from flywheel all the way to master cylinder. Excited to get another 1JZ back on the road.

Have you checked out the T-Shirt?! It’s a hot design, and the shirt is comfortable!

This gorgeous Soarer swapped SC300 equipped with a Non VVTI JZZ30 1JZ came in on a tow truck, within a couple hours had it purring, or shall I say growling like it’s supposed to. Now onto pulling trans to do a complete clutch job. 2023 starting off great! Let me know if you need any assistance with maintenance, general work, or fabrication! I’ll be happy to help!

Many stages it’s been through, it has to go up from here. Can’t wait.

These are fun to do. and myself replaced this oil pressure sensor on this 2014 Ford F150 4X4 this morning. Thanks for the assistance dude!

Stock 330CI with and goodies all around!
Doing some Drift Week prep for along with figuring out a bunch of issues. Hopefully once some new parts show up this thing will be a ripper and he will be testing it at

Had a little misfortune with this slave cylinder on this Wrong threaded bolts were used one too many times and it stripped the holes out completely. Tapped to M14X1.5 and used these awesome Nutserts to still utilize factory spec bolts.

and I mounted this fatty intercooler for to get him to the dyno tonight. Let’s make some power boiiii!

JZ things.

Cleaning day is the best refreshment for the garage.

Hyped on how this interior is coming out. Let us know if we can help you with any fabrication\installation needs!

For all the SR boys. Next shirt in the comic series. The comic SR20DET. Available now!

getting comfortable in the Z.

Out at with