CMD_Fabrication

Designed, laser cut, and bent some bed steaks for a customer yesterday. Great way to keep things in the bed of a truck or trailer..

Finishing up some whip / reverse light mounts for the Polaris Ranger and Can Am Defender. These heavy duty mounts are a great way to add whips as well as rear lighting to your ride!

https://cmd-fabrication.com/

Been a little busy with these custom laser cut tab tables for customers and decided to throw 1 together for myself along with a few useful tools.

3/16” laser cut and bent radiator supports for a customer.

Laser cut, countersink, and bent up some 12g 304 stainless tabs for a customer that’s refurbishing lockers.

Been super busy lately re-designing and cutting several different suspension parts for customers out of 4130 chromoly and sending them over to to throw some beautiful welds on these parts. From 3d scan to finished parts we can do quite a bit from 1 offs to full production.

Knocked out 10 Trophies in a day for a customer. Man that was fun finishing at midnight and dropping them off to a customer an hour away but I said I wouldn’t let them down!!

I’ve been super busy lately and I haven’t had much time to post on here but here’s a new fab table I laser cut out of 1/4” steel and welded up for the shop. Ive made several custom sizes and different variations of these tables for customers so if you’re interested in a table just pm me and I can help you out!!

Fixing up a few badly damaged things this week!! The forklift carriage is getting 2 new 1 1/4” plates welded on along with new stub shafts and the hydraulic cylinder needed a new ring welded on after the factory snapped off. The chip conveyor has been worn to nothing so I’m replacing it with some laser cut AR500 plate so it should last a little longer this time.

Fully fabricated and install guard rails done!! Let us save you $ as we do everything in house. No need to source expensive product from middle man stores when you can get everything direct from us!!

Ready for the

Couple different collapsible fire pits made for a customer. These came out nice!! 🔥

Another model 32 stand finished up along with a custom fab table knocked out for a customer!!

Couple hundred acrylic rock light covers knocked out for . We can laser cut just about anything. If you’re interested in custom product or you have product you would like produces send over a message for a free quote.

33 Guard rail post done and ready for powder coat. If you’re looking for product and looking to save some $$$ we would love to help you out just send me a pm with details and I’ll take care of you!!

Couple of winch mounts installed on a 40ft gooseneck to pull from up high or down low!!

Just finished up some custom 6ft tall 1/2” thick acrylic signs for Nutty Bolts. Next up is framing and adding LED lights then putting it in place..

Finally getting close to finishing up this trailer for King of hammer. Short deadline but we did it. Everything is going to powder coat after the event so raw steel will do for now!!

Threw together a couple different forklift wheel press plates that take about 400+ tons of pressure. All machined plates and tube to keep everything straight but also reduce some weight so it can be carried by hand although these aren’t light 😂.

I have a HUGE but SMALL favor to ask…

Go to my business page CMD_Fabrication then go to the 3 little dots…(on the side of page) 😎

- Hit “Invite Friends”
- Select "Invite All"
- Done
You’ve SUCCESSFULLY supported my business for $0.00 and less than 1 minute of your time.

📣 Thank you for supporting small and local businesses. I have already done so for several friends and I always try and support other small business owners! This is a great way for us to all network on social media for FREE!!

*I highly encourage my small business friends to copy this and use it!*

Little man putting in some work today in the new shop.. Gotta teach them while they are young.

Merry Christmas!!

Custom kitchen table laser cut from 3/16” steel and cerakote black with a heavy granite top. This thing weighs a ton!!

57 sheets of 1/8" steel ready to burn on the laser for a 5000pc order cut and bent. It's gonna be a fun week busting balls.

10 more display stands done. I'm loving this Miller Multimatic 225

Getting down on some aluminum tig today with the miller multimatic 225. I really love this machine!!